6 Reasons And Fixes For Baitcaster Drag Not Working

baitcaster drag not working
baitcaster drag not working

If you are an angler and like to spend your time in the water catching fish, you would already know the right drag settings on the baitcaster. However, the baitcaster doesn’t always work as supposed to. Having said that, what are you supposed to do when baitcaster drag not working issue occurs? With this article, we are sharing everything you must know about fixing the drag malfunctioning.

Baitcaster Drag Not Working

1. Set Drag On The Reels

To begin with, you need to use your hands for testing the drag rather than switching to the reel directly. For instance, if the dragline is not tight, it’s obvious that you need to tighten the drag – you can tighten it by turning the front drag adjustment button on the right side. On the other hand, if the drag is excessively tight, you can turn it on the left side for loosening up the drag. It is better to follow this drag adjustment system if your baitcaster has a closed face. However, if you aren’t satisfied with the drag accuracy, you can depend on a spring scale.

2. Bail Spring

The spinning wheels on the baitcaster are designed with bail springs but their ineffective performance will result in mechanical errors. When bail fails to open and stops working, it’s evident that something is wrong with bail springs. This issue can incur if you’ve been using the baitcaster for a long time or if its bail wire interrupted the performance. For this reason, it is important for you to inspect the external wire sides and see if its wire is bent – you simply need to replace the wire and bail springs will start working okay in case of bending. On the contrary, if the wire is fine, you’ve to switch to bail spring replacement – it can be pretty challenging, so ask a reel expert to help you out.

3. Paw

A damaged paw is another reason behind the drag not working. For those who don’t know, paw is designed to collect dirt, which means it’s prone to corrosion. So, when the paw continues collecting debris and dirt, it tens to go bad over the course of time. Similarly, when baitcaster’s paw is corroded and has dust, it fails to work. To fix this issue, you only need to open the paw and remove the grit and dirt from it. On the other hand, if the baitcaster’s paw is corroded, it is important to replace it and make sure to source paw from the reputed company. Lastly, it is important for you to clean the paw regularly to prevent corrosion.

4. Bearings

If you are a regular at angling, it is evident that the bearings will eventually wear out. We are saying this because old bearings can limit the functionality of baitcaster drag. This problem is also caused by grit and dirt, but it’s also common when the drag is always submerged in water. Having said that, you need to check the bearings and see if they have worn out. If that is the case, you need to change the bearings and switch to high-quality bearings. On the other hand, if the bearings are only dirty, take them off, dip them in a specialized metal cleaner, and the grit and dirt will be cleared.

5. Corrosion  

When it comes down to the baitcaster drag, the performance and functionality will be adversely impacted by corrosion. It is common for the baitcaster drag to become corroded when it is exposed to saltwater for a long time. For this reason, it is imperative that you clean the drag regularly as it helps prevent the chances of corrosion. In addition to this, reel must be replaced if the corrosion is too much to be cleaned. As far as level wind is concerned, opt for a toothbrush for cleaning it and don’t forget to wash the reels.

6. Excessive Lubrication

It is evident that lubrication is important for the baitcaster drag to function smoothly. However, excessive lubrication can also limit the performance of the drag. This is because over lubrication results in clogging, and you will be unable to rotate the handle. In case the lubrication is already too much, always use warm water for cleaning it up and always use lubricant as suggested by the manufacturer.

Leave a Comment