Minn Kota Riptide 70 is one of the most powerful saltwater trolling motors that you can install in your boat. Even if you live somewhere with rough water conditions, you won’t have to worry about much with this unit.
It is pretty easy to maneuver, and you can easily handle the motor through the remote controller. So, if you’re looking for a trolling motor that doesn’t bring power issues to your setup, then Minn Kota Riptide 70 is a good option.
With that said, quite a few users have asked about some common issues that you can face with this motor. So, if you’re also interested in Minn Kota Riptide 70 problems, the following details should give you a better perspective.
People should note that there are several reasons behind this issue. This is why it is essential that you go through all the different steps one by one.
This should help you in finding the exact reason behind the problem so that it can be fixed easily while preventing issues.
Troubleshooting Minn Kota Riptide 70 Problems
- Propeller Problems
Issues with the propeller not working perfectly is most common in the Minn Kota riptide units . It can lead to a variety of problems, from reduced performance to excessive vibration of the system.
So, it is best to isolate the problem quickly and fix the propeller if you’re struggling to manage the performance of your trolling motor.
Most often than not, you can get around this problem by removing the propeller from the assembly and rotating it a half-turn before putting it back on.
The complete instructions on removing the propeller are available in the owner’s manual, and you won’t need anything more than a few basic tools to get the propeller working again.
However, if you’re dealing with a broken propeller, then the only thing that you can do is install a replacement. It will be somewhat expensive, but at least you won’t have to worry about the performance issues again.
So, reach out to your dealer and source a compatible propeller for your Minn Kota riptide .
That way, you won’t have to deal with the same problem again. People having trouble trying to replace the propeller should consult the manual that came with your device.
This can help you with the process so that problems can be avoided. Other than this, some people report that the problem was from bent propeller fan blades. If this happens, then you can sometimes push the blades back into place.
Keep in mind that this is quite rare and there is a high chance that the blades might break. If this break then your only option will be to get these replaced with new ones.
- Steering Problems
There have been plenty of reports where users were complaining about steering problems with the Minn Kota Riptide 70.
A lot of factors can lead to this unit with the Minn Kota motor, and the best thing you can do to avoid this problem is to power cycle the controller and the motor.
If you’re lucky, then you won’t have to deal with any other steps, and the motor will start working perfectly.
However, if you’re still stuck in the same problem, then you’ll have to check the orientation of the drive collar with the motor. There is a good chance that the drive collar and motor are not engaged with each other.
You will have to tighten up the collar to get the system working again. So, make sure that there are no spaces between the collar and the motor before starting the system again.
Ideally, the issue should be fixed at this stage, and you won’t have to deal with any other Riptide problems.
Simply resetting the controller and engaging the collar are the only two things that you’ll need to get ahead of this problem with the Minn Kota Riptide steering system.
- Motor Shuts Down
Aside from these issues, some users have also reported problems with the motor shutting down after a few hours of operation.
This problem is either related to the quality of your power connections, or you’re dealing with overheating issues. So, you’ll have to check the thermostat and check the battery levels on your unit to fix the issue.
In most conditions, you won’t have to bother with anything more than recharging the battery.
However, if you’re not lucky and the issue persists, then you should grab a multimeter and the voltage output at the battery terminals.
Make sure also to clean the connection points and replace any wires that seem bent out of shape. Hopefully, that will fix the issue, and you won’t have to run into the same problem again.
All in all, these were a few common problems that you can run into while using the Minn Kota riptide unit. Most of these problems are quite easy to fix. You won’t have to take the unit to a professional.
However, if you’re still facing issues with your trolling motor, then make sure to reach out to Minn Kota support. They will guide you properly through the troubleshooting process, and you won’t have anything to worry about.
The battery usually lasts several years after which they start losing its tendency to hold a charge.
To prevent this from happening, it is important that you get the battery replaced with a new one before this. You can usually keep these in check to ensure issues can be avoided.
With that being said, you should also ensure that the problem is from the battery is old or not.
If the battery was new then there is a high chance that your issue might be from wires or corroded terminals. Start by checking the wires connected to the terminal and ensure these are tight.
If the connections were tight then your terminals are likely covered with dust. You can clear the clogs easily but if there is corrosion formed then use warm water to clear it.
This allows the corrosion to soften so that people can easily remove it.
After the corrosion has been removed, let the battery charge for some time and it should now work without any problems. If the issue persists, simply move on to the final step to get rid of the problem.
- Contact Customer Support Team
The steps mentioned above are enough for most people to ensure that they can fix the issues with their Minn Kota Riptide 70. In some cases, people report that even these troubleshooting steps were not enough.
If this happens then your only solution will be to contact the support team.
When it comes to this, it is important that you give the team, detailed information about your issue. This allows them to isolate the issue and ensure that the problem can be fixed quickly.
You should note that the process is fairly simple and also saves a lot of time.
You can also try finding the issue on your own but this will take a lot of time and it is also difficult. You also have to replace the faulty parts on your own which is why it is better that you avoid this.
Getting back to this solution, people should note that they can also get a warranty claimed.
This allows users to get free replacements and repairs so make sure that you go through the guidelines once. This helps in ensuring that your problem falls under warranty services.
My Minnkota70# salt water want turn with remote